- Note
- Published:
Moisture content variability in kiln-dried Gmelina arborea wood: effect of radial position and anatomical features
Journal of Wood Science volume 54, pages 318–322 (2008)
Abstract
Gmelina arborea is one of the most important species for plantation in tropical areas. However, high variability in final moisture content (MCf) is a problem in the drying process. This study sought to determine the variability in MCf in relation to distance from the pith (DP), and anatomic elements. Boards of 1.2 cm in thickness obtained from bark to the pith from 15-year-old plantation trees were dried in a pilot kiln. Anatomical characteristics, initial moisture content (MCi), and specific gravity (SG) were also determined. Pearson correlation matrix was conducted between MCf and the other variables. DP, fiber length, and ray width were correlated negatively with MCf, while fiber diameter was positively correlated. Other studied anatomical properties showed no statistical correlations. Other wood properties such as SG and MCi showed some influence on MCf. DP can be considered as a good practical predictor for MCf in G. arborea because some wood properties are related to MCf. However, other wood characteristics that are not related with DP also influence MCf, such as the presence of sapwood, MCi variation between and within trees, fiber diameter, and ray width. These results suggest that MCf variation in G. arborea is difficult to determine.
References
Dvorak WS (2004) World view of Gmelina arborea: opportunities and challenges. New Forest 28:111–126
Moya R (2004) Wood of Gmelina arborea in Costa Rica. New Forest 28:299–307
Lauridsen E, Kjaer E (2002) Provenance research in Gmelina arborea Linn. Roxb. A summary of results from three decades of research and a discussion of how to use them. Int For Rev 4:20–29
Sattar A, Sarkar S, Taukkdar Y (1991) Kiln drying of Gamar (Gmelina arborea) using varying sticker thickness and dryings schedules. Bangladesh J For Sci 20:49–54
Simpson W (1991) Properties of wood related to drying. In: Simpson W (ed) Dry kiln operator’s manual handbook AH-188. USDA Forest Service. Forest Products Laboratory, Madison, pp I1–I50
Pang S (2002) Effects of sawing pattern on lumber drying: model simulation and experimental investigation. Dry Technol 20:1769–1787
Holdridge L (1967) Life zone ecology. Tropical Science Center, San Jose, pp 19–32
ASTM International (2005) ANSI/ASTM D-143-94 (Reproved 2000) Standard methods of: small clear specimens of timber. ASTM International, West Conshohocken, vol 04–10
Johansen D (1940) Plant microtechnique. MacGraw-Hill, New York, pp 49–109
Sass J (1951) Botanical microtechnique, 2nd edn. Iowa State College Press, Iowa, pp 22–98
IAWA Committee (1989) List of microscopic features for hardwood identification. IAWA Bull 10:219–332
Snedecor GW, Cochran WG (1989) Statistical methods, 8th edn. Iowa State University Press, Ames, pp 177–196
Ohbayashi H, Shiokura T (1989) Anatomical structure of fastgrowing tropical tree species with differing growth rates. IAWA Bull 10:342–343
Ofori J, Brentuo B (2005) Green moisture content, basic density, shrinkage and drying characteristics of the wood of Cedrela odorata grown in Ghana. J Trop For Sci 17:211–223
Yamamoto K, Sulaiman O, Kitingan C, Choon L, Nhan N (2003) Moisture distribution in stems of Acacia mangium, A. auriculiformis and hybrid Acacia trees. Jpn Agr Res Q 37:207–212
Haygreen J, Bowyer J (1996) Forest products and wood science, 3rd edn. Iowa State University Press, Ames, pp 157–195
Moya R, Muñoz F (2008) Wet pockets in Gmelina arborea (Roxb.) dried lumber in trees from fast growth plantation. J Trop Forest Sci 20:48–56
Olsson T, Megnis M, Varna J, Lindberg H (2001) Study of the transverse liquid flow paths in pine and spruce using scanning electron microscopy. J Wood Sci 47:282–288
Zobel B, Sprague J (1998) Juvenile wood in trees. Springer, Berlin Heidelberg New York, pp 56–112
Möttönen V, Heräjärvi H, Koivunen H, Lindblad J (2004) Influence of felling season, drying method and within-tree location on the Brinell hardness and equilibrium moisture content of wood from 27–35-year-old Betula pendula. Scand J Forest Res 19:241–249
Siau J (1971) Flow in wood. Syracuse University Press, Syracuse, pp 11–68
Keey R, Nidjam J (2002) Moisture movement on drying softwood boards and kiln design. Dry Technol 20:1955–1974
Choong E, Peralta P, Shupe T (2001) Effect of hardwood vessels on longitudinal moisture diffusion. Wood Fiber Sci 33:159–165
Pearson R, Brown H (1932) Commercial timbers of India: their distribution, supplies, anatomical structure, physical and mechanical properties and uses, vol 2. Government of India Central Publication Branch, Calcutta, pp 799–803
Pang S (2002) Investigation of effects of wood variability and rheological properties on lumber drying: application of mathematical models. Chem Eng J 86:103–110
Chen Z, Lamb F (2004) A vacuum drying system for green hardwood parts. Dry Technol 22:577–595
Panevnik VI, Ivantsiv VM, Plyuta TI (1972) Monitoring wooddrying processes. Meas Tech 15:1435–1436
Cai Y, Hayashi K (2007) New monitoring concept of moisture content distribution in wood during RF/vacuum drying. J Wood Sci 53:1–4
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Muñoz, F., Moya, R. Moisture content variability in kiln-dried Gmelina arborea wood: effect of radial position and anatomical features. J Wood Sci 54, 318–322 (2008). https://doi.org/10.1007/s10086-008-0954-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10086-008-0954-8