Skip to main content
Journal of Wood Science

Official Journal of the Japan Wood Research Society

Download PDF

Evaluation of end-check propagation based on mode I fracture toughness of sugi (Cryptomeria japonica)

Journal of Wood Science volume 57, pages 371–376 (2011)Cite this article

Abstract

The relation between crack propagation based on fracture mechanics and end-check propagation during drying was evaluated in this study. Corresponding to the direction of end-check propagation, the mode I fracture toughness of air-dried sugi specimens in TR, TL, and intermediate systems was examined by single-edge-notched bending tests. The occurrence and propagation of end checks on sugi (Cryptomeria japonica D. Don) blocks during drying were observed at the scale of the annual rings. It was found that the critical stress intensity factor (K IC) decreased as the crack propagation changed from TL to TR. The value of K IC in the TR system was significantly lower than that in the TL system. As a measure of fracture energy, the area under the load-crack opening displacement curve in the TR system was more than twice that in the TL and intermediate systems. These results indicate that cracks perpendicular to the tangential direction initiate radially with ease, and then crack arrest occurs to prevent growing. This finding provides a consistent interpretation of the end-check propagation observed during drying as follows: tiny end checks, as an analog of TR cracks, occur easily and selectively in latewood or transition wood and propagate toward the pith during drying. When there is no corresponding secondary check in the forward latewood, the checks are arrested and do not propagate further.

References

  1. Simpson W (1999) Drying and control of moisture content and dimensional changes. In: Wood handbook: wood as an engineering material. General Technical Report FPL-GTR-113, US Department of Agriculture (USDA), Forest Service, Forest Products Laboratory, Madison

    Google Scholar 

  2. Murmanis L, River BH, Stewart H (1983) Microscopy of abrasiveplaned and knife-planed surfaces in wood-adhesive bonds. Wood Fiber Sci 15:102–115

    Google Scholar 

  3. Stehr M, Seltman J, Johansson I (1999) Laser ablation of machined wood surfaces. 1. Effect on end-grain gluing of pine (Pinus silvestris L.) and spruce (Picea abies Karst.). Holzforschung 53:93–103

    CAS  Google Scholar 

  4. Stehr M, Johansson I (2000) Weak boundary layers on wood surfaces. J Adhesion Sci Technol 14:1211–1224

    Article  CAS  Google Scholar 

  5. Stehr M, Östlund S (2000) An investigation of the crack tendency on wood surfaces after different machining operations. Holzforschung 54:427–436

    Article  CAS  Google Scholar 

  6. Schniewind AP, Ohgama T, Aoki T, Yamada T (1982) Effect of specific gravity, moisture content, and temperature on fracture toughness of wood. Wood Sci 15:101–109

    Google Scholar 

  7. Petterson RW, Bodig J (1983) Prediction of fracture toughness of conifers. Wood Fiber Sci 15:302–316

    Google Scholar 

  8. Sobue N, Asano A (1987) Effects of loading speed and moisture content on crack propagation in the radial direction of wood. Mokuzai Gakkaishi 33:7–11

    Google Scholar 

  9. Reiterer A, Tschegg S (2002) The influence of moisture content on the mode I fracture behavior of spruce wood. J Mater Sci 37:4487–4491

    Article  CAS  Google Scholar 

  10. Fujimoto N, Goto K, Mataki Y (1999) Fracture toughness of the surface layer of the boxed-heart square timber of Sugi associated with drying checks (in Japanese). Zairyo 48:223–228

    CAS  Google Scholar 

  11. Reiterer A (2001) The influence of temperature on the mode I fracture behavior of wood. J Mater Sci Lett 20:1905–1907

    Article  CAS  Google Scholar 

  12. Sobue N, Bajolet D, Pluvinage G (1985) Effect of drying stress on the fracture toughness of wood. Mokuzai Gakkaishi 31:528–531

    Google Scholar 

  13. Okamura H (1976) Introduction to linear fracture mechanics (in Japanese). Baihukan, Tokyo

    Google Scholar 

  14. Walsh PF (1972) Linear fracture mechanics in orthotropic materials. Eng Fract Mech 4:533–541

    Article  Google Scholar 

  15. Valentin G, Adjanohoun G (1992) Applicability of classical isotropic fracture mechanics specimens to wood crack propagation studies. Mater Struct 25:3–13

    Article  Google Scholar 

  16. Thuvander F, Berglund LA (2000) In situ observations of fracture mechanisms for radial cracks in wood. J Mater Sci 35:6277–6283

    Article  CAS  Google Scholar 

  17. Schniewind AP, Centeno JC (1973) Fracture toughness and duration of load factor I. Six principal systems of crack propagation and the duration factor for cracks propagating parallel to grain. Wood Fiber 5:152–159

    Google Scholar 

  18. Schniewind AP, Quarles SL, Lee S-H (1996) Wood fracture, acoustic emission, and the drying process, part 1. Acoustic emission associated with fracture. Wood Sci Technol 30:273–281

    Article  CAS  Google Scholar 

  19. Fonselius M, Riipola M (1992) Determination of fracture toughness of wood, J Struct Eng 118:1727–1740

    Article  Google Scholar 

  20. King MJ, Sutherland IJ, Le-Ngoc L (1999) Fracture toughness of wet and dry Pinus radiata. Holz als Roh- und Werkst 57:235–240

    Article  CAS  Google Scholar 

  21. Maruyama N, Okazaki H (1981) Cleavage fracture toughness of wood: Effects of annual ring angle on crack propagation (in Japanese). Bull Fac Agric Shizuoka 31:33–39

    Google Scholar 

  22. Harmuth H, Rieder K, Krobath M, Tschegg EK (1996) Investigation of the nonlinear fracture behavior of ordinary ceramic refractory materials. Mater Sci Eng A214:53–61

    Article  CAS  Google Scholar 

  23. Stanzl-Tschegg SE (2009) Fracture properties of wood and wood composites. Adv Eng Mater 11:600–606

    Article  CAS  Google Scholar 

  24. Hillerborg A (1991) Application of the fictitious crack model to different types of materials. Int J Fract 51:95–102

    CAS  Google Scholar 

  25. Thuvander F, Jernkvist LO, Gunnars J (2000) Influence of repetitive stiffness variation on crack growth behavior in wood. J Mater Sci 35:6259–6266

    Article  CAS  Google Scholar 

  26. Ando K, Sato K, Fushitani M (1991) Fracture toughness and acoustic emission characteristics of wood I. Effects of the location of a crack tip in an annual ring (in Japanese). Mokuzai Gakkaishi 37:1129–1134

    Google Scholar 

  27. Ando K, Ohta M (1999) Variability of fracture toughness by the crack tip position in an annual ring of coniferous wood. J Wood Sci 45:275–283

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Forestry and Forest Products Research Institute, 1 Matsunosato, Tsukuba, Ibaraki, 305-8687, Japan

    Ken Watanabe

  2. Department of Biomaterials Science, University of Tokyo, Tokyo, 113-8657, Japan

    Satoshi Shida & Masamitsu Ohta

Authors
  1. Ken Watanabe
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Satoshi Shida
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Masamitsu Ohta
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Ken Watanabe.

Rights and permissions

Reprints and Permissions

About this article

Cite this article

Watanabe, K., Shida, S. & Ohta, M. Evaluation of end-check propagation based on mode I fracture toughness of sugi (Cryptomeria japonica). J Wood Sci 57, 371–376 (2011). https://doi.org/10.1007/s10086-011-1187-9

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10086-011-1187-9

Key words

  • Fracture toughness
  • TR and TL systems
  • End check
  • Occurrence and propagation
  • Sugi
  • Drying